Chapter 4 – Supported Softwares Supported Software Chapter 4 – Supported Software Drivers, Utilities and Software Applications The CD that came with the system board contains drivers, utilities and software applications required to enhance the performance of the system board. The power button will not function once a keyboard password has been set in this field. The utility allows you to configure the Ethernet interface features and personal Firewall for optimized security. The modifications you have made will be written into the CMOS memory, and the system will reboot. None No floppy drive is installed K, 5. Drive A and Drive B These fields identify the types of floppy disk drives installed. IDE Prefetch Mode This allows data and addresses to be stored in the internal buffer of the chip, thus reducing access time.
|Date Added:||8 January 2004|
|File Size:||41.31 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Floppy Disk Drive Connector Hardware Installation Floppy Disk Drive Connector The system board is equipped with a 90 floppy disk drive connector that supports two standard floppy disk drives. If the system is configured with two hard drives, make sure the bootable first nc4 drive is configured as Master and the sec- ond hard drive is configured as Slave. Handle the clipper as shown in the illustration below.
Troubleshooting Appendix B – Troubleshooting B. Hardware Installation The system board requires a minimum of Watt power supply to operate.
DFI LANParty UT NF4 SLI-DR Expert Motherboard Review –
Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference.
None No floppy drive is installed K, 5. Refer to chapter 4 for more information about installing the USB 2. To prevent improper floppy cable installation, the floppy disk header has a keying mechanism. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.
The utility lanpartu you to configure the Ethernet interface features and personal Firewall for optimized security.
Page 90 BIOS Setup CPU Thermal-Throttling Thermal throttling regulates the thermal environment by alternating between running the processor at full speed and placing the processor in a sleep state whenever the upper limits of the thermal envelop are reached. Page 44 Hardware Installation Front Audio Jf4 front audio connector J4 on the Karajan audio module allows you to connect to the line-out and mic-in jacks that are at the front panel of your system.
Page 24 Hardware Installation 4. Hook Arm of the clipper Hook Position the clipper above the jumper cap. Chapter 4 – Supported Softwares Supported Software Chapter 4 – Supported Software Drivers, Utilities and Software Applications The CD that came with the system board contains drivers, utilities and software applications required to enhance the performance of the system board.
DFI LANParty Venus nF4 SLI-DR Expert Motherboard
If the system detected that its temperature exceeded the one set in this field, it will automatically shutdown. Enter text from picture: Don’t have an account? Shutdown Temperature You can prevent the system from overheating by selecting a tem- perature in this field.
The following will appear. If the serial device does not work, either the cable or the serial device has a problem.
Installing the CPU 1. In the actual CMOS setup, you have to use the scroll bar to view the fields. This section gives you functions to configure the system based on the specific features of the chipset.
To ensure that adequate power is provided, we strongly recommend that you use a minimum of Watt or greater power supply. Comments to lwn Manuals Your Name. Got it, continue to print.
DFI LANParty Venus nF4 SLI-DR Expert Motherboard – Hardware Secrets
Select the drivers you want to install. Align the SLI bridge included in the system board package above the SLI connector of the graphics cards then insert the bridge until it is properly seated in place. Although this function is supported, we do not recommend that you use a higher voltage because unstable current may be supplied to the system board causing damage. You can enter up to 5 characters.
The pin connector on the floppy cable can be placed into the header only if pin 1 of the connector is aligned with pin 1 of the header. System Error Message setting than indicated in Setup.
DFI LanParty nF4 User Manual
Install all necessary utility drivers then open the Display Properties dialog box. The default is Enabled. Page 62 Hardware Installation The system board requires a minimum of Watt power supply to operate.